Our broad line of floor coatings and varnishes beautify, protect and provide durability to any flooring surface. Explore our complete line of residential and commercial floor coatings to find the right one for your needs. We offer:
- Waterborne Clear Finishes for Concrete
- Solvent Borne Clear Finishes for Concrete
- Waterborne Pigmented Floor Coatings
- Solvent Borne Pigmented Floor Coatings
- Wood Floor Coatings
- Acrylic and Wax Floor Finishes
- Prep and Cleaners
Our floor coatings are formulated for quality durability and appearance—available in either water- or solvent-base.
Waterborne Clear Finishes for Concrete

1400 100% Solids 2K Epoxy – Clear Gloss
A high-gloss, high-build, clear coating formulated to provide a tough, protective finish for interior concrete floors. This two-component product is solvent-free making it zero VOC, very low odor, non-flammable, and minimal shrinking upon curing. It provides excellent resistance to abrasion, marring, scuffing, foot and vehicular traffic as well as chemicals including oil, grease, hydraulic fluid, gasoline, many solvents and moderate acids and alkalis. It is ideal for use in factories, warehouses, garage floors, covered parking decks, aircraft hangars, service stations, and other applications where a heavy-duty coating is required.
Technical Data Sheet PDF: 1400
4177 Waterbased Polyurethane
A zero VOC, zero HAP’s, low odor , catalyzed waterborne polyurethane. This product exhibits outstanding film hardness, impact, abrasion, corrosion, chemical, solvent, and UV resistance. It can be applied to interior or exterior, vertical or horizontal surfaces such as concrete, masonry, wood, aluminum, ferrous metal, and VCT. Excellent for use on floors or as a general purpose maintenance coating in industrial, commercial, and residential settings. Resists hot tire pick-up.
Technical Data Sheet PDF: 4177
1256 Floor Finish
Provides a glossy, wear resistant finish for tile and concrete floors. Covers 300-500 s/f per gallon.
Technical Data Sheet PDF: 1256

8001 Epoxy Concrete Seal
Clear, chemical resistant penetrating sealer. For use on new or old concrete. Extremely durable, low odor and rapid return to service.
Technical Data Sheet PDF: 8001
8005 100% Solids Two-part Epoxy Resurfacer
High solids, two-component epoxies intended to repair and protect concrete flooring. Resurfacer can be spread by squeegee, trowel, roller or brush to repair spalled/scaled concrete.
Technical Data Sheet PDF: 8005
Solvent Borne Clear Finishes for Concrete

7300 Low VOC Epoxy Sealer
Single component high gloss clear sealer for interior applications requiring good chemical and wear resistance.
Technical Data Sheet PDF: 7300
9640, 9665 Moisture Cure Urethane
Very hard surface resistant to Acid, alkali and chemicals. High gloss, 40% solids. 300-400 s/f per gallon. Aromatic Moisture Cure (9640) and Aliphatic Moisture Cure Urethane (9665).
Technical Data Sheet PDFs: 9640 and 9665
909 Polyamide Epoxy
Solvent based, two-component epoxy for severe use areas. Very durable and chemical resistant. Two colors and two tint bases.
Technical Data Sheet PDF: 909
1240LV Urethane Sealer
40% solids, glossy, durable finish with excellent chemical and abrasion resistance. Coverage is 300-400 s/f per gallon. Approved for use in USDA plants.
Technical Data Sheet PDF: 1240LV
Waterborne Pigmented Floor Coatings

8000 Series Waterbased Epoxy
Two-component, outstanding resistance to brake fluid, skydrol, etc. May be used on cured or uncured concrete, Unsurpassed for hardness, gloss and durability. Available in ten standard colors and a non-skid kit. Approved for use in USDA plants.
Technical Data Sheet PDF: 8000 Series

736 Series Dura-Gard
Waterbased polyurethane for interior or exterior use. Satin finish and abrasion resistant. Can be used on concrete, wood and metal for pedestrian applications. Available in eight colors and tint bases.
Technical Data Sheet PDF: 736
732 Series Acrylic Concrete Stain
Penetrating stain for use on new or properly prepared concrete floors. Resistant to peeling, easy to apply and easily recoated with various products. Available in seven colors.
Technical Data Sheet PDF: 732
730 Tred Safe Non-Skid
Waterbased non-skid perfect for multiple substrates, interior or exterior applications.
Technical Data Sheet PDF: 730

8005 100% Solids Two-part Epoxy Resurfacer
Excellent product for spalled or damaged concrete. High gloss and extremely durable. Great chemical and abrasion resistance. Zero VOCs. 100-200 s/f per gallon.
Technical Data Sheet PDF: 8005
Solvent Borne Pigmented Floor Coatings

739 Series Dura-Gard Floor & Trim
Polyurethane, high gloss, abrasion resistant finish for interior/exterior pedestrian use on concrete, wood and metal. Available in seven stock colors and three tint bases.
Technical Data Sheet PDF: 739
7300 Series Epoxy Ester Enamel
Single component, resistant to alkalis, acids, grease, oil and gasoline. High gloss finish, perfect for pedestrian traffic areas. Available in eight standard colors.
Technical Data Sheet PDF: 7300 Series

909 Polyamide Epoxy
Solvent based, two-component epoxy for severe use areas. Very durable and chemical resistant. Two colors and two tint bases.
Technical Data Sheet PDF: 909

4392-4393 Heavy Duty 2K Epoxy Non-Skid Coating
Two-component, high-build, solventborne coating that provides a slip resistant surface for dry and wet conditions. It resists abrasion, impact, water, salt, and mild chemicals. More durable than most one-component anti-slip coatings. Low VOC formulation (compliant for most areas). Use to provide a slip resistant surface over interior and exterior concrete and metal substrates. Ideal for warehouse and factory floors, aisle-ways, parking decks, loading docks, ramps, steps and other areas where a heavy-duty , non-skid coating is desired.
9015 Series Vehicular Safety Coating
Solvent borne, single component epoxy for interior use on concrete, wood and steel. Resistant to gasoline, acids and oils. May be used in heavy-use pedestrian or where forklift traffic is experienced. Coverage is 100 s/f per gallon. Approved for use in USDA plants. Stocked in eight colors.
9909 2K High Solids Epoxy Mastic
Solvent borne, two component epoxy for interior use on concrete, wood and steel. Resistant to gasoline, acids and oils. May be used in heavy-use pedestrian or where forklift traffic is experienced. Coverage is 100 s/f per gallon. Approved for use in USDA plants. Stocked in eight colors.
Technical Data Sheet PDF: 9909
Wood Floor Coatings
Our Excelsior wood floor coatings have protected and beautified wood floors for more than a century. A wide variety of coatings is offered to suit any application. Residential, educational, commercial and industrial use.
Solvent Borne Clear Finishes for Wood

Excelsior OMU Finish 350 Series
High gloss, light colored wood floor coating that dries to a hard, durable surface. Amber cast for warm glow and patina. MFMA approved.
Technical Data Sheet PDF: OMU Finish 350 Series
1040 Series Oil Modified Urethane
High gloss, traditional oil modified urethane finish designed to beautify and protect wood floors. Also available in Satin & Semi-gloss Finishes. MFMA approved.
Technical Data Sheet PDFs: 1040 and 1040LV
1035-LV Sanding Sealer
Lower solids allow deep penetration into new or completely stripped floors.
Technical Data Sheet PDF: 1035LV
9640 Moisture Cure Urethane
Very hard surface resistant to Acid, alkali and chemicals. High gloss, 40% solids. 300-400 s/f per gallon. Aromatic Moisture Cure (9640) and Aliphatic Moisture Cure Urethane (9665).
Technical Data Sheet PDF: 9640
Waterborne Clear Finishes for Wood

0400 Court Kote 1K
A waterborne, high gloss, polyurethane coating formulated for interior hardwood floors including maple, oak, pine, and parquet. This one-component, clear product is ideal for gymnasiums, racquetball courts, offices, and showroom floors as well as on wood work, railings, steps, and floors around the home.
Technical Data Sheet PDF: 0400
0500 Court Kote
An acrylic polyurethane with crosslinker for an extremely hard, scuff-resistant, crystal clear finish. Gloss and satin.
Technical Data Sheet PDF: 0500

1256 Synthetic Gym Floor Finish
Water-based emulsion that provides a glossy, wear resistant finish on synthetic sport floors or concrete floors. Not for use on wood gym floors.
Technical Data Sheet PDF: 1256
Acrylic and Wax Floor Finishes

4318-4325 High Speed Floor Finish
Acrylic fortified urethane for use on VCT tiles in heavy traffic areas. Can be buffed to restore gloss.
Technical Data Sheet PDF: 4318-4325
4518-4525 Acrylic Super Gloss Finish
Metal cross-linked copolymer. May be high speed buffed, applied with roller, pad or mop.
Technical Data Sheet PDF: 4518-4525
Prep and Cleaners
2123 Water-based Gym Floor Cleaner
Cleaning agent for use with waterborne wood floor finishes. Concentrated formula provides great value and can be diluted up to 10:1 to suit multiple applications. Removes dust mop treatment and skin oils that make floors slippery. Can also be used as a tacking agent prior to coating and dust mop treatment to keep floor clean.
Technical Data Sheet PDF: 2123
2120 HD Cleaner and Degreaser
Hard surface cleaner and degreaser for cleaning concrete and stripping acrylic finishes. Concentrated formula can be diluted to suit other applications such as cleaning floors, lockers, metal tanks, fans, grills, and motors. Approved for USDA plants.
Technical Data Sheet PDF: 2120
2090 All-Purpose Cleaner
Economical, concentrated detergent cleaning compound that can be diluted up to 20:1. Recommended for use on wood floors and all types of flooring materials, painted or enamel surfaces, woodwork, tile, finished metal, concrete, glass, etc.Contains no abrasives, solvents, acid, ammonia or caustic.
Technical Data Sheet PDF: 2090
1892 Liquid Acid Etch
Ready-to-use liquid acid etch and cleaner for surface preparation of unsealed concrete floors prior to applying a seal or finish. Can clean and etch in one operation. Opens surface pours to permit proper adhesion of finish.
Technical Data Sheet PDF: 1892
2702 Waterless Cleaner
Replace current text with: “Designed to clean wood surfaces where water is objectionable. Can be used as a tacking material for wood or concrete surfaces before applying a new coat of finish. Leaves no residue.
Technical Data Sheet PDF: 2702
Solvents and Other
We offer a variety of solvents for use in thinning and cleanup.
Harrison Paint Company
1329 Harrison Ave SW
Canton, OH 44706
330.455.5125
Contact